Microsoft LPF-00004 Manuale dell'Operatore Scaricare il pdf (Pagina 5)

IMPORTANT INFORMATION

CYBERAMP 380, COPYRIGHT MARCH 2002, AXON INSTRUMENTS, INC.

WARNING

IF THIS EQUIPMENT IS USED IN A

MANNER NOT SPECIFIED BY THE

MANUFACTURER, THE PROTECTION

PROVIDED BY THE EQUIPMENT MAY BE

IMPAIRED.

Power-Supply Voltage Selection and

Fuse Changing

Mains Supply Requirements

The CyberAmp 380 uses 30 Watts of power

and can operate from either two Mains

Supply voltages: 115 V~ or

230 V~. Variations in the voltage should

not exceed ±10%. Frequency can range

from 50 to 60 Hz. The CyberAmp is

intended for Installation Category II as

defined by IEC 664, as are all appliances

that use the Mains Supply.

Note: When shipped, the Mains Supply

fuse and fuse holder are removed from the

back of the CyberAmp 380 and placed in a

bag attached to the handle. All instruments

shipped from Axon Instruments are set for a

supply voltage of 115 V~. If the supply

voltage is not 115 V~, have a qualified

electronics technician perform the supply

voltage change procedure according to the

following instructions.

To change the supply voltage setting:

1. Disconnect the power cord.

2. For 115 V~ operation -- slide the switch

on the back panel towards the label

“115”. For 230 V~ operation -- slide the

switch on the back panel towards the

label “230”.

3. Reconnect the power cord.

Changing the Fuse

The CyberAmp 380 uses a 250 V~, T0.5A,

5 x 20 mm fuse.

In the event of fuse failure, disconnect the

power cord.

Before changing the fuse investigate the

reason for its failure.

To change the fuse:

1. Disconnect the power cord.

2. Use a screwdriver or a similar device to

rotate the fuse holder counterclockwise.

3. Replace the fuse with another fuse of

the same rating.

4. Reconnect the power cord.

Basic Equipment Setup and Safety

1. Supply and Earthing

Connections: Use the included IEC

power cord to connect the

instrument to a GROUNDED power

receptacle.

2. Mounting: Table or rack.

3. Use: Do not operate this equipment

with covers or panels removed.

Safe Environmental Conditions

1. Indoor use.

2. Mains supply fluctuations: not to exceed

±10% of the nominal voltage.

3. Temperature: between 5 ºC and

40 ºC.

4. Altitude: up to 2000 m

5. This instrument is designed to be used

under laboratory conditions. Operate

in a clean, dry environment only. Do

not operate in a wet or damp

environment.

WARNING

Shipping the CyberAmp 380

The CyberAmp 380 is a solidly built

instrument designed to survive shipping

around the world. However, in order to

avoid damage during shipping, the

CyberAmp 380 must be properly packaged.

In general, the best way to package the

CyberAmp 380 is in the original factory

carton. If this is no longer available, we

recommend that you carefully wrap the

CyberAmp 380 in at least three inches

(75 mm) of foam or "bubble-pack" sheeting.

The wrapped CyberAmp 380 should then

be placed in a sturdy cardboard carton.

Mark the outside of the box with the word

FRAGILE and an arrow showing which way

is up.

We do not recommend using loose foam

pellets to protect the CyberAmp 380. If the

carton is dropped by the shipper, there is a

good chance that the CyberAmp 380 will

shift within the loose pellet packaging and

be damaged.

If you need to ship your CyberAmp 380 to

another location, or back to the factory, and

you do not have a means to adequately

package it, Axon Instruments can ship the

proper packaging material to you for a small

fee. This may seem like an expense you

would like to avoid, but it is inexpensive

compared to the cost of repairing an

instrument that has sustained shipping

damage.

It is your responsibility to package the

instrument properly before shipping. If it is

not, and it is damaged, the shipper will not

honor your claim for compensation.

1 2 3 4 5 6 7 8 9 10 ... 156 157

Commenti su questo manuale

Nessun commento

Microsoft LPF-00004 Manuale dell'Operatore Pagina 5

Commenti su questo manuale

Prodotti e manuali riguardandi Misurazione, test & controllo Microsoft LPF-00004